Constant temperature water bath hh-6ad independent temperature control double row six hole intelligent temperature control welcome to buy

Hh-6ad six hole double case digital display independent constant temperature water bath

1、 Constant temperature water bath pot is widely used in distillation, drying, concentration and impregnation of chemicals or biological products.

2、 Instrument model:

Double row six hole independent constant temperature water bath
Studio size: 160x320x130mm
Overall dimension: 680x550x320mm
Heating power: 1800W
Temperature control range: 5-100 ℃
Temperature error: ± 0.5 ℃
Temperature fluctuation: ± 0.1 ℃

3、 Structure

This product is a flume type, with a maximum aperture of 12 cm on the mouth surface and a cover of four circles per hole. The inner pot is made of imported stainless steel. The shell is made of high-quality thin plate and sprayed with plastic. The electric heating tube is installed in the middle of water, which can heat quickly and save power consumption. It is equipped with a digital constant temperature device. The adjustment range is - 100 ° C, with an error of ± 1 ° C.

4、 Usage

When using, water must be added into the pot first, and then the power supply is connected. To set the temperature, press the set key to enter the temperature setting mode to set or view the set value. Press the set key to see the number flashing. In the setting mode, press the up button to increase the setting value and the down button to decrease the setting value. If you keep pressing the button, it will increase or decrease to the value you need. After setting, press the set button again to exit the setting mode and return to the normal working measurement mode.

2. Adjust parameter SC: press the set key for 3 seconds and enter the internal parameter setting adjustment interface. The interface shows that SC is the error calibration value, indicating the error between the measured value and the actual value of the temperature controller. The default value is 0.0. You can press the set key again to display the flashing number to enter the adjustment state (the following parameter setting method is the same), and press the up or down button to adjust the value. （-9.9~9.0）

E: After setting, press the set key to enter the next parameter adjustment. The interface shows that e represents the advance of breakpoint control (only effective when p value is set to 0). The default value is 0.5, and the adjustment method is the same as that of SC.

P: Then press the set key to enter the third parameter. The interface shows that P indicates the setting of P value, and the meaning of P value is roughly the starting control temperature = set value - (10 / P value). If it is set to 50 degrees, when p is 10, it means that 49 degrees begin to control; when p is 4, it means that adjustment begins at 47.5 degrees. If the temperature overshoot is too large, adjust the p value appropriately. If the temperature rises too slowly or the control temperature is not reached, adjust the p value appropriately.

Note: when p value is 0, the breakpoint control mode is entered. That is, the system PID fails. When the temperature is lower than (set value - E value)  , it will start heating, otherwise it will stop heating.

c: Then press the set key to enter the setting of the last parameter C. the last parameter is reserved for the system temporarily. Please do not adjust it. The default value is 20.0. After setting all parameters, press set key to return to normal working state. Do not add too much water in the pot, so as to avoid water overflowing out of the boiler when boiling. Pay attention to that the water in the pot can not make the electric heating pipe out of the water surface, so as to avoid burning the electric heating pipe and causing water leakage.

5、 Precautions

(1) In order to ensure safety, please connect the ground wire when using.
(2) Do not add water and dry burn.
(3) When not working, the power should be cut off to prevent accidents.

Changzhou Runhua Electric Appliance Co., Ltd
Address: No.26, Jinsheng East Road, Jintan City, Jiangsu Province
website: www.runhuayiqi.com
Email: 394514722@qq.com
Tel: 0519-82305398 Fax: 0519-82306938

No video highlights...